BashBench
A father and his teenage son smiling beside a backyard dirt track lined with black drain pipe, a small orange off-road truck on a dirt mound in front of them

How to build an RC car track sized to the car you drive

Most track plans skip the one number that matters: how wide the lanes are compared with your car. Start there, then pick a surface and one of three layouts.

How we pick · Updated · We earn a commission when you buy through our Amazon links.

Size the track to the car first: lanes about three times the car's width and the tightest turn no smaller than one car length on the inside. Then pick a surface you already have (driveway, yard dirt or a basement floor), lay out one of the three plans below with cones or drain pipe, and drive it before you dig anything. A 1/24 car gets a real track on a sheet of plywood. A 1/10 truck needs a slice of yard.

How we put this together

We read the track-building guides that rank for this topic on Oct 21, 2026: FMS Hobby's track design guide, the Hobbico PVC track instructions RC Car Action republished, and an RCTalk thread where club members describe how they handle soil and drainage. An Instructables backyard build and RCTech threads wouldn't load for us, so we use only their search summaries, and say so where we do. Car sizes come from retailer spec listings. The lane and turn rules below are our own starting points, worked out from those sizes, not a published standard. Amazon picks come from searches on the same day. How we research.

Size the track to the car

None of the guides we read gives a lane width per scale, and it's the thing that decides whether a track is fun or a crash fest. Here is the rule we use. One car needs a lane about three times its width, so it can drift wide in a turn and still recover. The inside of the tightest turn should be at least one car length in radius, or 2WD cars spin and 4WD cars push straight on. Racing two or three cars side by side needs more, and the at-least-5-feet figure in the Instructables build's search summary fits that.

ScaleExample car (listed size)Lane, one carLane, 2 or 3 carsTightest inside turn radiusSmallest oval
1/24Axial SCX24: about 7.8 x 3.9 in (199 x 99 mm)12 in18 to 20 in8 inAbout 3.5 x 8 ft (a plywood sheet)
1/16Traxxas Mini Slash 4X4: 16 x 8.5 in (408 x 215 mm)26 in3 to 4 ft16 inAbout 7 x 17 ft
1/10Traxxas Slash 4X4: 22.4 x 11.7 in (568 x 296 mm)3 ft5 ft2 ftAbout 10 x 25 ft (14 x 30 ft with 5 ft lanes)

The smallest oval is just the arithmetic: two turn radii plus two lane widths across, and about two and a half times that long so there's a straight worth the name. Build it bigger if the space allows. Drift cars are the exception. A car sliding at 45 degrees takes up about as much lane as its own length, so for a drift loop make lanes about two car lengths wide. If you're still choosing a car, our RC scale sizes guide shows how big each scale really is.

Pick the surface you already have

The cheapest track is the one you don't have to pour or haul in. Match the surface to the car, not the other way around.

SurfaceGood forCostWorkWatch out for
Driveway or parking padShort course trucks, touring cars, driftCones onlyMinutesThe street; rough concrete also eats tires
Mowed grass4WD monster trucksFreeMow it shortLow cars and 2WD buggies bog down
Packed dirtBuggies and short course trucksLow, more if you buy clayA weekend with a rake and tamperDrainage and weeds
Basement or garage carpet1/18 to 1/24 cars, micro buggiesLow to medium (carpet)An afternoonCarpet needs a day or two to lie flat (FMS)
Sealed concrete floorDrift cars, mini on-roadBarriers onlyAn afternoonDust kills grip; sweep before each session

Three layouts that work

Each plan below is drawn for one scale but scales up or down with the lane table. Lay it out with cones or string first and drive it for a few packs. The FMS guide's advice is sound: keep your first layout simple, because a flowing track is more fun than a tight technical one.

1. Driveway cone course (1/10, about 20 x 40 ft)

Driveway cone course for 1/10 cars A top-down plan of a 20 by 40 foot driveway. The start is at bottom left. Cars run up a straight, through a five-cone slalom with cones about 6 feet apart, around a hairpin marked by two cones at the far end, and back down a sweeper to the finish. The street side is marked as off limits. START / FINISH5-cone slalom, cones about 6 ft aparthairpin garage street side: off limits, park a car or set a barrier here

No digging and no cost beyond a bag of cones. Space slalom cones about three car lengths apart (6 ft for a 1/10 truck) and tighten them as drivers improve. Run it away from the street: put a parked car or a row of sandbags across the open end so a truck that gets away from someone stops there.

2. Backyard dirt oval with a berm and a jump (1/10, about 30 x 50 ft)

Backyard dirt oval with infield chicane A top-down plan of an oval dirt track about 30 by 50 feet with lanes about 5 feet wide. A banked berm wraps the far turn, a single jump sits on the back straight, a chicane cuts through the infield, sandbags sit at the ends of both straights, and the drivers stand on a raised spot outside the near straight. A drain tile runs to the lowest corner. jumpberm infield chicane (optional) driver stand drain tile to low corner sandbags

The classic. Borders are flexible drain pipe, the berm is dirt piled on the outside of the far turn and packed hard, and the sandbags go where cars arrive fastest, at the ends of the straights. The Hobbico track instructions put sandbags in exactly those spots. The infield chicane is a second line you can open or close, which answers the RCTalk advice to build so the layout can change and you're not running the same lap forever.

3. Garage or basement drift loop (1/24 to 1/10 drift)

Garage drift loop A top-down plan of a kidney-shaped drift loop on a smooth floor. It has a long sweeping corner at one end, a tight hairpin at the other, and a left-right transition in the middle. Low barriers line the outside edge and a few clipping-point markers sit on the inside of each corner. Lanes are about two car lengths wide. long sweepertight hairpin left-right transition dots = clipping points; outer line = barriers

Drifting rewards rhythm, so this loop links a long sweeper to a hairpin through a left-right transition. Put a cone or dot at the inside clipping point of each corner. Sweep the floor before each session; dust on sealed concrete ruins grip faster than anything else. If you're shopping for a car to run here, see the best RC drift cars.

Two friends kneeling on a basement floor, grinning and pointing at a small track outlined with red and white border strips and orange cones
A basement floor, a bag of barriers and an afternoon is all a small-scale track needs.

Building a backyard dirt track, step by step

  1. Plan on paper. It was the first tip from an RCTalk club member, and it saves digging the same berm twice. Mark where drivers will stand and where a car that leaves the track ends up.
  2. Clear the ground of grass and roots, then rake the area smooth. FMS suggests a sod cutter if you're taking up lawn.
  3. Mark it out with stakes and string or spray paint, and drive it with cones before you commit.
  4. Fix the dirt. An RCTalk builder mixes clay into the soil so the surface packs and grips, and RCTech threads (search summaries only) warn that pure clay bakes rock hard. Mix it into the native soil. Sand helps drainage.
  5. Shape berms and jumps. Pile dirt on the outside of turns for berms and pack it hard. One RCTalk builder short on dirt makes a wooden frame, like a skateboard ramp without the top, and fills it with dirt so the jump's sides don't slump.
  6. Lay the borders. Flexible drain pipe bends around turns. The RCTalk tip that holds the shape best: drill a hole about every 2 feet and drive long gutter spikes through it. The Instructables build's summary mentions rebar stakes for the same job.
  7. Water and tamp. FMS says to sprinkle the dirt and tamp it down for a harder, longer-lasting surface. A hand tamper does a small track. The RCTalk club does big moves with a skid steer and finishes small areas by hand.

Want a jump on the back straight? A packed dirt tabletop is the easiest to live with, and a wooden kicker gives more air. Our RC car ramp guide has build dimensions and angles for each scale, plus what to do about landings.

Drainage, the part everyone skips

A dirt track that holds water is a mud pit for days after every rain. Pick a spot that already drains if you can. If not, an RCTalk member's method is to grade the track so water funnels to one or two dead spots, lay drain tile there and fill over it. Their club also tills sawdust and mulch into the surface in spring, which helps the dirt hold moisture without turning to soup. And don't treat a puddle as a water feature until you've read whether your RC car is actually waterproof.

Indoor and carpet tracks

Indoors, the Hobbico method is hard to beat for cost: PVC pipe cut to length and joined with couplers makes the borders, with sandbags on the outside of high-speed spots. For small bumps, it lays a carpet remnant over short pieces of pipe; for a rumble strip, a cut-down trellis taped down. Lay carpet and let it settle flat for a day or two before you tape the edges, as FMS suggests. Micro buggies and 1/18 to 1/24 cars are the right size for a basement, and a car like the Losi Micro-B (an RTR 2WD micro buggy, 400+ bought last month) turns a rec room into a race night.

What to buy (and what not to)

Most of a home track is free dirt and scrap. The few things worth buying:

Skip old tires as borders unless they're buried; FMS notes they can be harsh on cars. Skip anything metal with an edge.

Make it safe to drive

FMS's rule is the one to build around: don't aim fast sections at people or anything fragile. Put the driver stand where drivers can see the whole track and nobody stands at the end of a straight. Keep the run-off on the outside of fast turns clear. If kids are driving, check the age grade on the car: most hobby-grade trucks run LiPo packs, and Horizon's lithium battery safety document says they're not for children under 14, so an adult owns the charging.

Which car for which track

A dirt oval suits a 2WD or 4WD buggy, stadium truck or short course truck; our best RC cars for beginners starts there. Grass and big jumps are monster truck country, covered in the best RC monster trucks. Crawlers need a slow, technical course instead, which we cover in RC crawler course ideas.

Start with cones on the driveway this weekend. If you're still using it a month later, that's when to rent the tamper.

Sources: FMS Hobby, "Building Your First RC Track" (Jun 2025); Hobbico DIY track instructions via RC Car Action; Instructables "Backyard R/C Track" (search summary only); RCTalk "Looking to build a backyard track" thread; RCTech backyard track threads (search summaries only); retailer spec listings for the Axial SCX24, Traxxas Mini Slash 4X4 and Slash 4X4; Amazon listings checked October 21, 2026. How we research · Affiliate disclosure

Questions people ask

How wide should an RC car track be?
Make each lane about three times your car's width for one car, and wider if two or three cars will run together. For a 1/10 short course truck that's about 3 feet for one car; the search summary of an Instructables backyard build suggests at least 5 feet so a few cars fit. A 1/24 car needs only about a foot.
What is the best surface for a backyard RC track?
Packed dirt with some clay in it. Clay helps the surface hold together and grip, and an RCTalk builder mixes it into the soil. RCTech threads warn that pure clay bakes hard (we could only see their search summaries), so mix it with the native soil or a little sand. Water it and tamp it, and it gets firmer each time.
How do you make borders for an RC track?
Flexible black drain pipe is the usual answer, pinned with rebar or long gutter spikes through holes drilled every couple of feet. Indoors, use PVC pipe held with sandbags or click-together plastic barriers. Avoid anything with a hard edge that can snap an arm.
How much space do you need for an RC track?
Less than you think if you size it to the car. A 1/24 oval fits on a 4 x 8 foot sheet, a 1/16 loop fits in a one-car garage bay, and a 1/10 oval needs roughly a 10 x 25 foot patch of yard at minimum.
Can you build an RC drift track at home?
Yes. A smooth sealed concrete garage or basement floor works, with plastic barriers or foam pipe to mark the loop. Drift cars travel sideways, so make the lanes about two car lengths wide instead of three car widths.
How do you keep an RC dirt track from turning to mud?
Build on ground that sheds water, grade the low spots so water runs to one place, and lay drain tile there under the dirt. One RCTalk club member says they till sawdust and mulch into the track each spring to help it hold moisture without turning to soup.